downscaling from 1080p to 720p in SPLASH PRO
Posted: Mon Jun 28, 2010 8:57 pm
SPLASH PRO uses downscaling 1080p to 720p. Why?
Mirillis forum
Mirillis forum
https://mirillis.com/forum/
downscaling from 1080p to 720p in SPLASH PRO
Page 1 of 1
Re: downscaling from 1080p to 720p in SPLASH PRO
Posted: Mon Jun 28, 2010 9:40 pm
What? Haven't noticed
Re: downscaling from 1080p to 720p in SPLASH PRO
Posted: Tue Jun 29, 2010 4:03 am
Same here
You need provide more info (e.g. video container, video format, etc.)
You need provide more info (e.g. video container, video format, etc.)
Re: downscaling from 1080p to 720p in SPLASH PRO
Posted: Tue Jun 29, 2010 11:00 am
For Example Gamer 1080p:
Video
ID : 1
Format : AVC
Format/Info : Advanced Video Codec
Format profile : High@L4.1
Format settings, CABAC : Yes
Format settings, ReFrames : 4 frames
Muxing mode : Container profile=Unknown@4.1
Codec ID : V_MPEG4/ISO/AVC
Duration : 1h 34mn
Bit rate : 10.3 Mbps
Nominal bit rate : 10.5 Mbps
Width : 1 920 pixels
Height : 1 040 pixels
Display aspect ratio : 16:9
Frame rate : 23.976 fps
Resolution : 8 bits
Colorimetry : 4:2:0
Scan type : Progressive
Bits/(Pixel*Frame) : 0.214
Stream size : 6.78 GiB (88%)
Writing library : x264 core 79 r1342 e8501ef
Encoding settings : cabac=1 / ref=4 / deblock=1:0:0 / analyse=0x3:0x133 / me=umh / subme=7 / psy=1 / psy_rd=1.0:0.0 / mixed_ref=1 / me_range=16 / chroma_me=1 / trellis=1 / 8x8dct=1 / cqm=0 / deadzone=21,11 / chroma_qp_offset=-2 / threads=6 / nr=0 / decimate=1 / mbaff=0 / constrained_intra=0 / bframes=3 / b_pyramid=0 / b_adapt=1 / b_bias=0 / direct=1 / wpredb=1 / wpredp=2 / keyint=250 / keyint_min=25 / scenecut=40 / rc_lookahead=1 / rc=2pass / mbtree=1 / bitrate=10489 / ratetol=1.0 / qcomp=0.60 / qpmin=10 / qpmax=51 / qpstep=4 / cplxblur=20.0 / qblur=0.5 / ip_ratio=1.40 / aq=1:1.00
Language : English
Playing with splash pro (with nvidia pure video). It is Full HD when motion 2 is turned off. But if it is on, picture became more greased like in 720p. Need to use Detail Boost to restore clearness, but it give more artefacts.
Is there way to use motion 2 with smooth motion but without grease???
Video
ID : 1
Format : AVC
Format/Info : Advanced Video Codec
Format profile : High@L4.1
Format settings, CABAC : Yes
Format settings, ReFrames : 4 frames
Muxing mode : Container profile=Unknown@4.1
Codec ID : V_MPEG4/ISO/AVC
Duration : 1h 34mn
Bit rate : 10.3 Mbps
Nominal bit rate : 10.5 Mbps
Width : 1 920 pixels
Height : 1 040 pixels
Display aspect ratio : 16:9
Frame rate : 23.976 fps
Resolution : 8 bits
Colorimetry : 4:2:0
Scan type : Progressive
Bits/(Pixel*Frame) : 0.214
Stream size : 6.78 GiB (88%)
Writing library : x264 core 79 r1342 e8501ef
Encoding settings : cabac=1 / ref=4 / deblock=1:0:0 / analyse=0x3:0x133 / me=umh / subme=7 / psy=1 / psy_rd=1.0:0.0 / mixed_ref=1 / me_range=16 / chroma_me=1 / trellis=1 / 8x8dct=1 / cqm=0 / deadzone=21,11 / chroma_qp_offset=-2 / threads=6 / nr=0 / decimate=1 / mbaff=0 / constrained_intra=0 / bframes=3 / b_pyramid=0 / b_adapt=1 / b_bias=0 / direct=1 / wpredb=1 / wpredp=2 / keyint=250 / keyint_min=25 / scenecut=40 / rc_lookahead=1 / rc=2pass / mbtree=1 / bitrate=10489 / ratetol=1.0 / qcomp=0.60 / qpmin=10 / qpmax=51 / qpstep=4 / cplxblur=20.0 / qblur=0.5 / ip_ratio=1.40 / aq=1:1.00
Language : English
Playing with splash pro (with nvidia pure video). It is Full HD when motion 2 is turned off. But if it is on, picture became more greased like in 720p. Need to use Detail Boost to restore clearness, but it give more artefacts.
Is there way to use motion 2 with smooth motion but without grease???
Re: downscaling from 1080p to 720p in SPLASH PRO
Posted: Tue Jun 29, 2010 11:33 am
An update is scheduled for July. So you should seem of improvements
http://www.mirillis.com/forum/viewtopic.php?f=18&t=337
http://www.mirillis.com/forum/viewtopic.php?f=18&t=337